SAM9-L9260 Hacking

From Hive76 Wiki
Revision as of 15:00, 13 January 2010 by FarMcKon (talk | contribs) (Setup the Toolchain (Debian based system))
Jump to: navigation, search

A couple of SAM9 Boards are around the space (see for spec's). Here is how to setup for them.

Setup dev machine (Linux)

We have attempted setup on OSX and on Windows. In both cases, it was hard to get the project working. So instead we are working with Linux (Ubuntu 9.04) for our development.

  • Install Ubuntu

Bootloader (SAM)

1) The first thing to check is your bootloader, to make sure you can load code onto the board. 2) Download the bootloader (called SAM-BA) from the Atmel website, as part of the sam-ba_cdc_2.9.linux_cdc CD. That CD contains the linux tools for general Atmel ARM development. 3) Download some pre-built projects to test. You can download a CD image with a bunch of prebuilt projects from Atmel called at91sam9260-ek That disk will contain a directory 'packages' which is full of pre-built example projects, including the completed binaries. 4) Connect to the board Connecting to the board via SAM-BA is annoyingly complicated, and a bit wonky. It's bad bad design, and took a bit to figure out. To make a long process short, you have to munge the 'usbserial' kernel module. 4a) setup the machine That means you need to unload it if it's loaded, reload it with some custom settings, and then check it connected ok. Details on the computer side of that process are at ( TODO: add link to / 4b) Setup the board For the board itself (the Olimex SAM9-L9260) you will also have to pull a couple of jumpers to get the programmer to connect properly. Unplug the board from the computer, and from the wall, and pull off jumper DF_E and jumper NAND_E. AFAIK (check this) that prevents the board from booting from flash or NAND flash, and it will default to a reprorgamming mode. (insert photo) 4c) Run SAM-BA While those jumpers are removed, plug power into the board. The reconenct the jumpers and connect the USB cable from your computer to the SAM9-L9260 board. The check at the command line if '/dev/ttyUSB?' exists. If that is there, If you then run SAM-BA (having done 1 - 4) you should see the /dev/ttyUSB? listed as connection, and you should be able to select the board 'at91sam9260-ek' in the 'select your board' menu. Click connect to connect to the board. 5) Load a program: TODO


The SAM9-L9260 does not seem to run the prebuilt binaries from the Atmel CD. The atmel data comes as binaries SDRam NORFlash. We tried loading them into DFlash, NANDFlash, and other sections of the chip, and it didn't work. Assuming that is because the Olimex board is different from the official Atmel board.

  • DF_E is linked to SAM-BA memory system Dataflash SPI0 CS1
  • NANDF_E is linked to SAM-BA memory system NandFlash (no chip select for it)

USB connection

Document here how to get a USB -> serial dongle working, using the magic of modeprobe and rmmod, etc. We have a script for it. Base it on

Boot Order Details

The 9260 tries to boot in the following order

  • DataFlash CS0
  • DataFlash CS1
  • NandFlash
  • Samba Monitor (USB or DBGU) until connection or reboot.

Compile Examples from Atmel for Olimex board

How to compile code to run off of a flash card or USB drive plugged into a Olimex SAM9-L9260 dev board running linux, based on Debian Lenny EnDebian is a site dedicated to getting Debian running on embedded devices, they have info on cross compilers and more. Cross tool chain binaries are at

Setup the Toolchain (Debian based system)

  1. Follow the instructions at this emdebian page.
  2. TODO list wiki and/or static setup page
  3. From the command line, run 'arm-linux-gnueabi-gcc-4.3 -v' to make sure you have it installed and working.
  4. Find the example 'hello world' program at the end of SAM9-L9260.pdf document from olimex. Save it to a file.
  5. run 'arm-linux-gnueabi-gcc-4.3 -o hello hello.c' to compile the program
  6. copy program to a flash drive
  7. log into the board using minicom (on linux)
  8. run 'mkdir /mnt/DRIVENAME' to make a mount point for the flashdirve.
  9. run 'mount /dev/disk/by-label/NEATHACKER /mnt/NEATHACKER -t auto'

Misc Notes

Note:Atmel has some good examples of launch-able firmware for testing the SAM9260, but they compile for Nand flash (the atmel demo board) not nor flash (the olimex board). NOTE: we use minicom to connect to the board. NOTE: linux on SAM9-L9260 is Linux sam9-l9260 2.6.31-rc3-olimex #1 PREEMPT Thu Jul 16 17:00:14 EEST 2009 armx NOTE: sam9-l9260:/mnt/NEATHACKER# /sys/devices/platform/ at91_mci/ at91_udc/ atmel_usart.1/ leds-gpio/ at91_ohci/ atmel_nand/ atmel_usart.2/ macb/ at91_rtt.0/ atmel_usart.0/ atmel_usart.3/